juniper jn0-522 JNCIA-FWV braindumps
- Wednesday, July 15, 2009, 20:39
- Cert Tests
- 1,274 views
- 6 comments
Exam Name: FXV,Associate (JNCIA-FWV)
Exam Type: Juniper
Exam Code: JN0-522 Total Questions: 140 Which ScreenOS CLI command would be used to view traffic logs?
A. Get traffic
B. Get log policy
C. Get policy log
D. Get log traffic
Answer: D
What are two benefits of configuring a ScreenOS device in transparent mode? (Choose two.)
A. There is no need to reconfigure the IP addresses of routers or protected servers.
B. There is no need to create MIPs or VIPs for incoming traffic to reach protected servers.
C. Policies are easier to create since you do not have to include source and destination IP
addresses.
D. The product can support more VPNs and obtain greater throughput because there is less
overhead to manage.
Answer: A, B
In the flow decision process, the system has found a route entry matching the packet destination
IP. Which pair will identify the policy that is applied to this packet?
A. Source and destination MAC
B. Source and destination interface
C. Source and destination TCP port
D. Source and destination IP address
Answer: B
Which command is used when configuring web management on the VLAN1 interface for a client
connected to an e3 interface in the DMZ zone?
A. set int eth3 manage web
B. set zone v1-dmz manage web
C. set int dmz zone manage web
D. set int VLAN1 zone dmz manage web
Answer: B
When a firewall receives the first packet in a series, what will it immediately do?
A. Check its route table.
B. Check its session table.
C. Determine if traffic is crossing zones.
D. Verify that it is not malformed or a fragment.
Answer: D
Which statement about address configuration is correct?
A. Address groups cannot be used with VPN policies.
B. Address groups must be associated with a single zone.
C. You can create address groups as needed from within a policy.
D. You cannot reference individual addresses once they have been added to a group.
Answer: B
Your VPN is failing during Phase 2 negotiation, and you are the initiator. You check your local
event log and see IPSec messages but no failures. What is the next logical troubleshooting step?
A. View the event log of the responding gateway.
B. Configure the peer-id on your local IKE gateway.
C. Double check routing reacheability to the remote network.
D. Turn on logging in the policy and check the event logs again.
Answer: A
You are looking at the event log of the initiating device and it says, Received notify message for
DOI <1> <14>
A. Phase 2 PFS failure
B. Phase 1 gateway failure
C. Phase 1 proposal mismatch
D. Phase 2 proposal mismatch
Answer: D
|
Type |
Exam Bible | New Questions & Answers |
Latest Updated |
Download link |
| All Certbible 's Exam Dumps |
597 |
1 days ago | Available |
PassGuide Training Materials & Practice Tests
About the Author
Free Certification Exam Download has written 10018 stories on this site.
If you have any doubts about legality of content or you have another suspicions, feel free to contact us:CertGuard@Gmail.com
6 Comments on “juniper jn0-522 JNCIA-FWV braindumps”
Write a Comment
Gravatars are small images that can show your personality. You can get your gravatar for free today!
You can get Latest Certification Dump of JNO-522 at jno.dump@gmail.com, Guarantee assured 100 % Score with this Dump
R/sir, if any one have a JN0-522 and JN0-100 dumps, kindly send me,
Best regards;
Shujaat Hassan
shujaat.hassan@yahoo.com, shujaat.hassan@nadra.gov.pk
Sir i need JNO-100 and JNCIS-SEC dumps
If someone have these dumps than please forward me on my e-mail address.
“alvi88@gmail.com”
If someone have dumps for JN0-522, plz send me. avzalov@mail.ru
anybody have jno-100 dumps please send to my email :sujithkanathil02@gmail.com
Hi all, I need JNO-100 and JNCIS-SEC dumps