passguide jn0-360

PASSGUIDES JuniperNetworks PASSGUIDES JN0-360 Training Tools undoubtedly prepare you best for your upcoming JN0-360 Certification Exam. Our JN0-360 Exam Study Tools are prepared by Professionals and Trainers who know the JN0-360 Exam Objectives and keep an eye on latest JN0-360 Exam Objectives to bring the latest JN0-360 Study Material to you. Our JN0-360 Study Material is not only updated regularly but also provides your fastest success guarantee in your next JN0-360 Certification Exam. Our JN0-360 Study Tools are for every one including but not limited to JN0-360 Study Guides, JN0-360 Questions and Answers, JN0-360 Audio Learning, JN0-360 Preparation Labs and JN0-360 Practice Testing Software. All of our JN0-360 Study Material is matched by none other in the industry and provides a prompt success with relatively very less preparation time.Question: 1
What are two valid actions that can be applied to a frame by a Layer 2 firewall filter? (Choose two.)

B. loss-priority
C. sample
D. count

Answer: C

Question: 2
Which two statements describe differences between IPv4 and IPv6? (Choose two.)

A. IPsec is built into IPv6.
B. IPv6 uses a 32-bit (4-byte) address and can support up to 4,294,967,296 addresses.
C. IPv4 supports extension headers whereas IPv6 options are integrated into the base.
D. IPv6 eliminates the need for NAT.

Answer: A

Question: 3
You must configure an OSPF area that does not accept type 3 link-state advertisements (LSAs) from area 0 (other than the default route). You have configured your area to be stub, but you still see type 3 LSAs.
What will account for this behavior?

A. You should have configured your area as totally stubby.
B. You should have used a not-so-stubby-area.
C. You are experiencing a routing loop.
D. You have exported routes into OSPF.

Answer: D

Question: 4
You have configured an IP-IP tunnel between Router A and Router B.
Which Junos operational mode command is used to verify that the tunnel interface is up and operational?

A. show chassis tunnel status
B. show tunnel interface
C, show interfaces terse
D. show interfaces tunnel

Answer: B

Question: 5
Which IS-IS packet is used to determine the level of an IS-IS neighbor?


Answer: C

Question: 6
Router A is an OSPF router connected to both Area 0 and Area 1. Area1 has been configured as a stub area.
Which two LSA types does Router A suppress from Area 1? (Choose two.)

A. Router LSA
B. External LSA
C. Summary LSA
D. ASBR Summary LSA

Answer: A

PassGuide Cisco Exams Questions & Training Materials

  1. Free Passguide nortel 920-259 exam
  2. Free How to filter OSPF routes that have the same source ip
  3. Free Passguide Enterasys 2B0-011 Exam
  4. Free PassGuide jncia jn0-331 pdf demo
  5. Free passguide HP ASE HP0-790
  6. Free passguide HP0-790
  7. Free Bridging the gap between 3550 and 3560 QoS: Part II
  8. Free PassGuide JNO-100 & JNO-331 Full Test Engine
  9. Free passguide HP0-Y12
  10. Free [offer] LinuxCBT IPv6 Edition ISO
  11. Free Passguide Computer Associates CA Exam 270-420
  12. Free passguide HP ASE HP0-205

About the Author

PassGuide Free Certification Exam Download has written 6442 stories on this site.

If you have any doubts about legality of content or you have another suspicions, feel free to contact

Write a Comment

Gravatars are small images that can show your personality. You can get your gravatar for free today!

You must be logged in to post a comment.

Copyright © 2019 CertBible – IT certifications Exams,Study Guide,Practice Test,Training Materials.. PassGuide,Testinside,Pass4side,Certifyme,Transcender,Examworx,Topcerts,Actualtests. microsoft Comptia MCSE Oracle hp ibm citrix Sitemap